MDF processing
MDF processing
ถ้าดูให้ดี ภายใต้เฟอร์นิเจอร์ หรือที่ตู้ที่ยังประกอบไม่เสร็จเผยให้เห็นเนื้อไม้ข้างใน คุณอาจสังเกตเห็นว่าไม้มีความสม่ำเสมอและไม่มีเมล็ด นั่นเป็นเพราะมันไม่ใช่ไม้ธรรมชาติ แต่เป็นแผ่นใยไม้อัดความหนาแน่นปานกลาง (MDF) MDF เป็นผลิตภัณฑ์ไม้ที่ถูกออกแบบให้ง่ายต่อการทาสี และการประกอบเข้าด้วยกัน ใช้แผ่นไม้อัดไม้กับไม้ธรรมชาติเลียนแบบ มันแพงน้อยกว่าไม้ธรรมชาติและส่วนใหญ่ใช้ในอาคารเนื่องจากความต้านทานความชื้นไม่ดี
ความชื้นเป็นพารามิเตอร์ที่สำคัญมากในการผลิตแผ่น MDF เนื่องจากปริมาณความชื้นจะเป็นตัวกำหนดความแข็งแรงและความทนทานโดยรวมของบอร์ด ลักษณะพื้นผิว / คุณภาพของบอร์ดควบคุมโดยการกระจายความชื้น
MDF Manufacturing Process
Debarking & DigesterMDF Production Moisture Measurement
Wood chips are prepared starting with logs that are debarked, chipped and screened. The chips are washed then softened in a steam-pressurized digester. The softened chips are transported to a pressurized refiner chamber where single or double revolving disks are used to mechanically pulp the softened chips into fibers suitable for making the board.
Drying & Blending
From the refiners, the fibers move to the drying and blending area. Single-stage or multiple-stage drying systems are used to reduce the moisture content of the fibers to the desired level. Resin, wax, and in some cases urea water are added to the softened fiber which is flash-dried while being conveyed to a bin.
Forming Line & Pressing
The dried fibers pass through a grader and are laid out in a mat which is consolidated at the forming pre-press. Next, the hot press converts the mat into a panel through the application of high pressure and temperature.
Finishing Line & Packaging
After pressing, the boards are cooled, sanded, trimmed, and sawed to final dimensions. The boards may also be painted or laminated. Finally, the finished product is packaged for shipment.
Quality Parameters and Measuring PointsMCT460-WP moisture sensor for MDF production
Moisture, resin and wax measurements can be made simultaneously using a Process Sensors Corporation (PSC) Near Infrared (NIR) sensor at multiple locations within the MDF manufacturing process.
Moisture of green wood chips (pre-digester) can be measured to calculate dryer load and to control the feed rate of the dryer. Typical moisture range is between 45 and 150% dry weight, so without feed rate control the dryer can be overloaded.
Post-dryer moisture measurement is taken on the refined fiber at the exit of the refiner, and the moisture range is typically 30 to 55% dry weight.
On the preformed mat, the moisture range is 0 to 5%.
Installation Locations
A PSC moisture sensor is typically mounted within 6 to 16” of the product and is either looking directly at wood chips and fiber or through a glass window. The moisture sensor can also be fitted with a snorkel sampler to measure moisture of fiber freefalling in a chute. The sensor’s analog outputs are typically connected to the process controls system allowing the end-user to monitor their process and log historical data.
If the plant layout makes it impractical to mount an online sensor, a PSC QuikCheck benchtop analyzer can be used in the laboratory for quick, accurate and reliable sample testing.
Value and Quality
Incoming strands vary significantly in moisture content and composition. Measuring moisture at multiple locations with sensors from Process Sensors Corporation allows temperature and process speed to be adjusted automatically, ensuring that high quality, consistent panels are produced as efficiently as possible.
